Support (Moderator: Johannes @ Robots in Architecture)

Making a command list that works...

Started by Woodboss

5 Replies
18,871 Views

November 23, 2017, 12:03:04 PM
by Johannes @ Robots in Architecture

Importing SRC files

Started by edulopes

3 Replies
18,932 Views

November 25, 2016, 01:10:49 PM
by Johannes @ Robots in Architecture

Robots stops shortly when output is switched off

Started by Brodesser83

6 Replies
18,984 Views

September 05, 2019, 05:57:28 PM
by Johannes @ Robots in Architecture

Turntable setup with Linear axis

Started by Hyperbot

5 Replies
19,057 Views

December 14, 2018, 05:43:18 PM
by Johannes @ Robots in Architecture

stepper motor have vibration when receive value E1 from stream real time

Started by Settawat

7 Replies
19,206 Views

June 09, 2021, 03:11:32 PM
by Johannes @ Robots in Architecture

Clockwise turntable with weird tool path preview

Started by yyh1002

3 Replies
19,338 Views

October 11, 2019, 08:35:31 AM
by yyh1002

KUKA_Sunrise_Communicator _ No output AXIS/POS/FORCE

Started by avishek

8 Replies
19,395 Views

June 09, 2021, 01:07:44 PM
by Johannes @ Robots in Architecture

Converting E6POS with S/T to E6AXIS

Started by antl

3 Replies
19,577 Views

April 12, 2018, 04:45:16 PM
by Johannes @ Robots in Architecture

KUKAprc for Dynamo

Started by Christian

5 Replies
19,594 Views

January 09, 2018, 07:56:49 AM
by Johannes @ Robots in Architecture

KR C2 sr x11 diagram

Started by Sigi

2 Replies
19,663 Views

October 22, 2024, 07:46:09 PM
by Sigi

Robot, creator, conveyor and sensor. KUKA simulation software

Started by bomigaro3

1 Replies
19,693 Views

June 28, 2015, 05:09:45 PM
by Johannes @ Robots in Architecture

KUKA PRC and Stäubli RX170HP 6-Axis

Started by kerber.g

3 Replies
19,757 Views

January 26, 2016, 08:18:18 AM
by ludo

which robots will the gh plug in work with?

Started by kerber.g

1 Replies
19,771 Views

May 30, 2014, 10:45:43 PM
by Johannes @ Robots in Architecture

Control a plasma cutter : Modbus or CPC ?

Started by Xylotica

2 Replies
19,819 Views

January 27, 2016, 03:36:04 PM
by Xylotica

sunrise communicator - axis and pos outputs nothing

Started by victorlin

7 Replies
19,864 Views

May 31, 2020, 09:24:36 PM
by Johannes @ Robots in Architecture

Tool direction on surface

Started by CUE_STRATHCLYDE

1 Replies
19,934 Views

July 24, 2014, 12:19:05 AM
by Johannes @ Robots in Architecture

Issues of Correlation of Starting Points Between Robot and GH Simulation.

Started by tenn6064

6 Replies
19,937 Views

May 16, 2024, 01:33:57 PM
by alicebell

pick and place algorithm with grasshopper

Started by freesheida1984

7 Replies
19,993 Views

April 08, 2024, 05:42:00 PM
by Johannes @ Robots in Architecture

Orient component not getting parts flat for cutting?

Started by Woodboss

6 Replies
20,013 Views

March 05, 2018, 07:32:52 PM
by Woodboss

<SYS-X44> Error during ECat stack initialization [NetworkResponse() iiwa

Started by DIA_Sina Mostafavi

6 Replies
20,113 Views

November 26, 2021, 08:45:26 PM
by Johannes @ Robots in Architecture