Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - robotmey

#1
Support / Re: Floppy ? / Network Share
February 21, 2022, 10:33:55 PM
I have read almost all posts but unfortunately with no result. username and password must be 'administrator' and 'kuka',because it needs these username and password each time I stop VxWorks and I want to go to the windows. 
defender is enabled but firewall is disabled. are they related to network credential?
#2
Support / Re: Floppy ? / Network Share
February 21, 2022, 09:57:44 AM
I tried all Usernames and Passwords but still network credential doesn't allow to acess to shared folder because of "wrong username or password" :(

any idea?
#3
Support / Re: Floppy ? / Network Share
February 15, 2022, 11:39:57 AM
Hello all,

KUKA Side: KRC2 Ed.05, windows XP SP2
PC Side: Windows 10

I want to share a folder in KUKA for easier files tranfering between my laptop and KUKA PC. I have done this steps:

1. setting convinient IP Address and Subnet Mask between two PC's
Result: according to the ping, two PC's can see each other with successful send and recieve data packages.

2. creating new local user group in windows XP with these properties:
Username: KUKA
Password: kuka

3. creating new folder in D:\ drive in windows XP and sharing it for everyone with full permission (read/write).

4. srearchnig KUKA IP address in laptop explorer (my case: \\192.168.1.2)

in this step, windows 10 need to enter network credentials. when I enter username and password from step 2, can't access to my shared folder and it complaining about 'wrong username or password'  issue.

I found three ways to disable network credentials in windows but there is no effect and it still needs proper username and password.

can somebody help please where I am doing wrong?
#4
General Discussion / KUKA 8th axis wiring
February 04, 2021, 08:47:31 AM
hello

KSS V5.4.14

I have configured one external axis to our robot and it is working without any problem. Now I need to add the 8th axis. unfortunately I can't find any document related to wiring of KSD supply or motor brake for 8th axis...can anybody help?
#5
General Discussion / Re: TCP coordinate
October 17, 2019, 12:10:29 PM
thanks for reply,

sorry but i am still confuse. If in current tool & Base menu, l set my tool number to my defined TCP and Null frame for the base. can i see fixed values of TCP relative to the robot base in Robot position menu for insert in Post processor?

#6
General Discussion / TCP coordinate
October 17, 2019, 11:53:42 AM
hello dear users,


KUKA KRC2, v4.1.5, Milling application with Powermill

post processor needs TCP Coordinates relative to the robot base. I Know every tool is defined by XYZABC values defining the offset from

the 6th axis flange. manually I changed B=-90 so TCP coordinates direction is similar to the world coordinate. now i need right values

of TCP coordinate relative to the robot base. is there any way to see these values on the pendant?



thanks for any help

#7
General Discussion / sharing network directory
June 16, 2019, 08:08:54 AM
Hello all


I have an KUKA KRC1 Controller with WIN95 OS. I have installed new windows and KRC and want to share a derive between my PC

(WIN7) and KUKA controller with a cross LAN cable. I have attached a picture of my network configuration menu in controller side. I set

IP address/ Subnet mask and shared a drive, unfortunately nothing happened and i can't see any shared drive. can somebody help me

is it require something else to install in controller side for setting up the IP address?


thanks for any help