Support (Moderator: Johannes @ Robots in Architecture)

setup robot with turn table and linear rail

Started by oleg

4 Replies
13,228 Views

April 26, 2023, 08:59:40 AM
by oleg

Problem with KR C4

Started by OTTOOL

5 Replies
19,652 Views

October 17, 2017, 09:29:14 AM
by Johannes @ Robots in Architecture

Fusion 360 NC Import

Started by OTTOOL

2 Replies
12,614 Views

June 29, 2018, 07:08:34 PM
by Johannes @ Robots in Architecture

Custom Variables

Started by oveliz_80

3 Replies
15,339 Views

July 16, 2024, 01:41:31 PM
by Johannes @ Robots in Architecture

Offset 0,0,0 on custom base

Started by OXIDO

1 Replies
14,026 Views

March 18, 2025, 04:52:14 PM
by Johannes @ Robots in Architecture

Adding text programing to the commands?

Started by OXIDO

2 Replies
12,156 Views

September 06, 2023, 11:21:15 AM
by OXIDO

Re oriant planes for turn table E1 and E2

Started by OXIDO

8 Replies
20,641 Views

April 01, 2025, 07:50:17 AM
by Johannes @ Robots in Architecture

KUKA prc settings (Start and end Position)

Started by OXIDO

1 Replies
13,048 Views

January 14, 2025, 03:03:58 PM
by Johannes @ Robots in Architecture

Load diffrent Workstations

Started by OXIDO

1 Replies
11,032 Views

January 30, 2023, 09:56:38 AM
by singline

How to use Fusion 360 G code with KUKA Prc ?

Started by OXIDO

2 Replies
12,033 Views

March 01, 2023, 08:10:57 AM
by Johannes @ Robots in Architecture

keeping the tool oriantation constant

Started by OXIDO

1 Replies
10,213 Views

July 10, 2025, 10:44:41 PM
by Johannes @ Robots in Architecture

Turntable with 3D curve

Started by OXIDO

2 Replies
12,834 Views

March 27, 2024, 08:44:53 AM
by OXIDO

Reset robot to home in middle of programs...

Started by OXIDO

1 Replies
14,288 Views

December 04, 2024, 04:15:26 PM
by Johannes @ Robots in Architecture

Follow a NURBCurve

Started by OXIDO

3 Replies
13,164 Views

November 22, 2023, 03:03:22 PM
by Johannes @ Robots in Architecture

Collsion check on RAM.

Started by OXIDO

2 Replies
13,927 Views

May 20, 2025, 08:56:55 AM
by OXIDO

Custom tool with two work planes

Started by OXIDO

1 Replies
13,687 Views

November 29, 2024, 11:03:58 AM
by Johannes @ Robots in Architecture

Smooth movements of a Turn table?

Started by OXIDO

1 Replies
11,226 Views

September 15, 2023, 04:03:24 PM
by Johannes @ Robots in Architecture

Woven CMD not working

Started by OXIDO

5 Replies
14,296 Views

April 25, 2023, 09:23:10 AM
by Savonia3D

Horizontal turn table

Started by pak

4 Replies
14,565 Views

July 06, 2018, 11:24:33 AM
by pak

Robot moving on X,Y right by on Z it's goes way lower than it's should

Started by patchara

1 Replies
12,398 Views

June 14, 2024, 10:29:09 AM
by Johannes @ Robots in Architecture