Support (Moderator: Johannes @ Robots in Architecture)

SPLINE is too long> error in kuka

Started by OXIDO

7 Replies
496 Views

March 12, 2026, 08:59:26 AM
by Johannes @ Robots in Architecture

KUKA prc settings (Start and end Position)

Started by OXIDO

1 Replies
14,726 Views

January 14, 2025, 03:03:58 PM
by Johannes @ Robots in Architecture

Setting axis preferences

Started by OXIDO

1 Replies
492 Views

December 05, 2025, 03:55:18 PM
by Johannes @ Robots in Architecture

Collsion check on RAM.

Started by OXIDO

2 Replies
18,110 Views

May 20, 2025, 08:56:55 AM
by OXIDO

Smooth movements of a Turn table?

Started by OXIDO

1 Replies
12,530 Views

September 15, 2023, 04:03:24 PM
by Johannes @ Robots in Architecture

Custom tool with two work planes

Started by OXIDO

1 Replies
15,352 Views

November 29, 2024, 11:03:58 AM
by Johannes @ Robots in Architecture

Reset robot to home in middle of programs...

Started by OXIDO

1 Replies
16,049 Views

December 04, 2024, 04:15:26 PM
by Johannes @ Robots in Architecture

Adding text programing to the commands?

Started by OXIDO

2 Replies
13,546 Views

September 06, 2023, 11:21:15 AM
by OXIDO

keeping the tool oriantation constant

Started by OXIDO

1 Replies
14,064 Views

July 10, 2025, 10:44:41 PM
by Johannes @ Robots in Architecture

Re oriant planes for turn table E1 and E2

Started by OXIDO

8 Replies
27,444 Views

April 01, 2025, 07:50:17 AM
by Johannes @ Robots in Architecture

Programing for multible tables

Started by OXIDO

1 Replies
296 Views

January 15, 2026, 05:42:52 PM
by Johannes @ Robots in Architecture

Horizontal turn table

Started by pak

4 Replies
15,750 Views

July 06, 2018, 11:24:33 AM
by pak

Robot moving on X,Y right by on Z it's goes way lower than it's should

Started by patchara

1 Replies
13,911 Views

June 14, 2024, 10:29:09 AM
by Johannes @ Robots in Architecture

Undetected Unreachable Position and Unnecessary Axis Rotation

Started by pawelsapiecha

4 Replies
15,939 Views

February 19, 2021, 07:14:39 AM
by pawelsapiecha

LIN movement generating random 90º turn at specific point

Started by pedrovarela

6 Replies
22,545 Views

March 10, 2016, 07:37:29 PM
by pedrovarela

HWC - static tool, moving block

Started by petebooth

3 Replies
21,165 Views

May 19, 2015, 08:11:52 AM
by Johannes @ Robots in Architecture

axis limits and galapogus

Started by petebooth

1 Replies
13,296 Views

October 05, 2018, 10:55:36 AM
by Johannes @ Robots in Architecture

set base by numeric input

Started by petebooth

2 Replies
15,584 Views

September 07, 2017, 09:04:15 AM
by petebooth

KUKA|prc 2 crash when opening KUKA|prc CORE settings

Started by PetterJhon

1 Replies
12,307 Views

July 22, 2019, 07:35:19 AM
by Johannes @ Robots in Architecture

Weaving a Wait Command

Started by pmrichardson4

2 Replies
16,606 Views

November 09, 2016, 06:30:43 PM
by pmrichardson4