Support (Moderator: Johannes @ Robots in Architecture)

got error ip adress after open kuka robot

Started by Settawat

4 Replies
22,968 Views

November 29, 2024, 02:09:59 PM
by Johannes @ Robots in Architecture

Reset robot to home in middle of programs...

Started by OXIDO

1 Replies
16,483 Views

December 04, 2024, 04:15:26 PM
by Johannes @ Robots in Architecture

Turntable location change unreachable axis

Started by STurner

1 Replies
15,317 Views

December 12, 2024, 07:41:38 AM
by Johannes @ Robots in Architecture

Custom Robot - KR8 Hollow Wrist

Started by benlawson

6 Replies
21,026 Views

December 12, 2024, 06:12:54 PM
by Johannes @ Robots in Architecture

Custom Tool Axis Issue

Started by tjroy

3 Replies
18,177 Views

December 20, 2024, 08:53:04 AM
by Johannes @ Robots in Architecture

Prevent Rotation of Tool

Started by tjroy

2 Replies
17,686 Views

December 20, 2024, 04:48:55 PM
by tjroy

KUKA prc settings (Start and end Position)

Started by OXIDO

1 Replies
15,270 Views

January 14, 2025, 03:03:58 PM
by Johannes @ Robots in Architecture

spline tree error

Started by wyattarmstrong

8 Replies
28,424 Views

January 24, 2025, 05:57:28 PM
by Johannes @ Robots in Architecture

Etracting the RPY (roll pitch yaw) from the $pos_act variable

Started by luispacheco

2 Replies
16,966 Views

January 31, 2025, 06:54:33 PM
by luispacheco

KUKA Robot Speed, Settings & Calibration

Started by clari

5 Replies
29,473 Views

February 06, 2025, 11:11:13 AM
by Johannes @ Robots in Architecture

Casting Goo to KUKA|prc Command

Started by MkMrA2

4 Replies
21,014 Views

February 10, 2025, 10:50:37 PM
by MkMrA2

Inaccurate Robot Movement

Started by clari

1 Replies
17,083 Views

February 11, 2025, 10:48:35 PM
by Johannes @ Robots in Architecture

How can i install KUKA prc multiaxis version?

Started by fethi.m

1 Replies
17,792 Views

February 17, 2025, 06:08:42 PM
by Johannes @ Robots in Architecture

Adjusting approach angle of Kuka Tool to specified point

Started by tjroy

4 Replies
21,850 Views

March 05, 2025, 07:01:05 PM
by tjroy

Offset 0,0,0 on custom base

Started by OXIDO

1 Replies
17,816 Views

March 18, 2025, 04:52:14 PM
by Johannes @ Robots in Architecture

Re oriant planes for turn table E1 and E2

Started by OXIDO

8 Replies
28,238 Views

April 01, 2025, 07:50:17 AM
by Johannes @ Robots in Architecture

Output Problem while Developing C# script in VS

Started by mehradmahnia

8 Replies
28,485 Views

April 07, 2025, 08:50:46 PM
by Johannes @ Robots in Architecture

Understanding G-code to KRL Conversion for Extruder Control

Started by federgarrido

6 Replies
27,638 Views

May 05, 2025, 05:53:04 PM
by Johannes @ Robots in Architecture

Collsion check on RAM.

Started by OXIDO

2 Replies
18,838 Views

May 20, 2025, 08:56:55 AM
by OXIDO

Axis values of current Robot position during KUKA|prc Simulation

Started by MartinDembski

1 Replies
18,390 Views

May 26, 2025, 08:02:17 AM
by Johannes @ Robots in Architecture